Extraordinary epoxy composite. This material can be applied on wet steel with firmly adherent rust, copper, aluminum and other substrates. On steel it passivates corrosion. Great for hydroblasted surfaces. Requires only DW1/DW2 prep. No climatizing required. Passed new DNV Norsok 6000 hour tests for ballast tanks.

Use for ballast tanks, double hulls, void areas, bulkheads, wet spaces, bilge areas, heavy condensate areas, grey water tanks, or where tradiitonal surface preparation is difficult. 100% solids formula with zero VOC's. Light Gray, Dark Gray, or Red Oxide can be primer, Intermiate and Finish coats. All other colors are topcoats over one of these prime colors.

NO HARMFUL SOLVENT VAPOURS.	No more problems with DEW POINT.	Application on vessel's while sailing.
NO VOC's = 100% solids.	Fast curing.	No profile necessary for good adhesion.
Superior impact resistance.	Excellent substrate and intercoat adhesion.	Compatible with steel, iron. stainless steel, galvanized steel, concrete and fiberglass. Optimal application is on steel or iron. Other more suitable products area available for other substrates
NON FLAMMABLE.	Cost savings on surface preparation.
Good chemical resistance	Excellent anticorrosive properties

SHIPS, OFFSHORE & MARINE STRUCTURES.	Ballast tanks, Fresh water tanks, Fuel/Crude oil tanks, Decks, Bilge areas, Wet spaces, Void areas, Double bottoms, Offshore platforms, Rigs, Machinery, and excellent as Deck pass-way coating.
STRUCTURAL STEEL & EQUIPMENT.	Bridges, Trestles, Railroad cars, Metallic structures, Lead covered casings etc....
PIPE COATINGS	Suitable for direct application on exterior and interior potable water pipes lines, Fuel lines.
TANK LINING	Potable Water, Fuel Storage, Food and some chemicals.

EURO-basic ES301 , is an excellent 100% solids anticorrosive epoxy coating for iron or steel surfaces meeting special requirements not fulfilled by the traditional epoxy specifications. EURO-basic ES301, is ecologically formulated and designed to be applied directly on wet or dry surfaces. Compatible with new or aged iron/steel, tightly adherent rust, and over existing coatings which are firmly bonded to surface. EURO-basic ES301, does not need any primer as it can be applied as a primer, intermediate or finishing coat.

Vehicle Type / Pigment Type	Modified epoxy/Amine composite - Chemical resistant pigments.
Colours	ES301-00 (White), ES301-10 (Light Grey), ES301-41 (Deck Green), ES301-60 (Red), ES301-62 (Redoxide), ES301-99 (Black), or custom request.
Finish	Semi-gloss
Solvent type	Not applicable
Mixing Ratio	5 ( base ) : 1 ( curing agent ) by weight. 3 ( base ) : 1 ( curing agent ) by volume
Curing Agent	"L" 301D00 "K" 301D02
Viscosity	92 Ku at 23ºC ( 73,4ºF )
Specific Gravity	1,34 Kg/dm³
Volume of Solids	100%
Pot Life	"L" Version 25ºC ( 75ºF ) - 45 minutes / "K" Version 30ºC (86ºF) - 3 Hrs
Flash Point	200ºC ( 392ºF )
Leaching Rate	Not applicable
Theoretical Covering Capacity	7,46 Sq.m/Kg. ( 36,42 Sq.ft/Lb. ) at 100 microns ( 4 mil )
Recommended Film Thickness	Wet: 100 microns ( 4 mil ); - Dry: 100 microns ( 4 mil )
Application Method	Brush, Roller, Airless Spray Tip: 21 (range18-28) thou. Outlet Pressure: 210 Kg/cm² ( 3000 psi )
Overcoating Time	"L" Version Touch: 2 hrs. - Hard: 6 hrs. at 23ºC ( 73,4ºF) Min: 3 hrs. at 23ºC ( 73,4ºF ) - Max.: 7 days. If maximum overcoat time period exceeded, rough up surface or reactivate surface with solvent ( TH03 )
Thinner	Material: none - Cleaning: TH03
VOC ( Volatic Organic Compound )	Does not contain. It is a 100% solids epoxy product
Ambient Temperature	Min: > 0ºC ( 32ºF ) - Max.: Not applicable. Substrate is the important factor When applying below oºC ( 32ºF ), a different cure is required. In case of any doubt, contact your local Euronavy agent
Substrate Ambient Temperature	Min: 0ºC ( 32ºF ) - Max.: 50ºC ( 122ºF )
Cautions	Self. When applying on top of aged coatings, make sure they are in sound conditions.
Packing	Product is a two pack component, available in 1 - 5 - 20 Kg., combined packs
Transport Code	Resin: Non Hazardous / Non Flammable. Curing: UN 2651. Law Nº6 of humanly harmful chemical management code.
Storage Conditions	Resin: 5ºC ( 41ºF ) and 40ºC ( 104ºF ) not more than 2 years Curing Agent: 15ºC ( 59ºF ) and 40ºC ( 104ºF ) not more than 2 years
Approvals	Lloyd's Register, U.S.Navy, Germsnischer Lloyd, Rinave and LNEC

EURO-basic ES301, is designed for application over iron/steel surfaces pre-treated by power tool St3 degree of the Swedish Standard SIS 055900, DW2 of German Standard STG 2222 or SSPC-SP 2, 3, 4 and 10.

Best performance will be achieved by treating all surfaces with EURO-cleaner F2 - SL15, followed by high pressure wash before applying EURO-basic ES301.

Most aged epoxies have recoating limitations. Contact your local Euronavy agent, for recommendations.

EURO-basic ES301, is a two pack product, which contains the proper ratio of ingredients. The entire contents of each container must be mixed together, as supplied. Stir base first to obtain smooth homogenous condition not longer than 2 minutes. After obtaining a uniform base, add the curing agent slowly to the base under continuos stirring for 3 minutes. The use of a speed adjustable power mixer is recommended. Do not over agitate as this, will accelerate cure and lower life of product.

Higher temperatures will reduce pot life of the mixture. Lower temperatures will increase it.

EURO-basic ES301 can be applied, by conventional spray airless, brush or roller. When airless equipment is used, a Graco 30:1 Bulldog or 45:1 Senator or larger pumps is recommended. A 0,21 to 0,25 tip size will provide a good spray pattern. For optimum results, insure that equipment and fluid lines are clean, free of water or solvents. Longer hose length or cold temperatures may require an increase in pump ratio. Care should be taken that proper and uniform film thickness is obtained. The recommended spray angle is 40º / 70º. Product may be applied on wet or dry surfaces in 100% humid conditions.

Tank Coating System - Two coats of EURO-basic ES301, at 100 microns ( 4 mil ) per coat, plus two stripe coats over sharp edges, cut-outs and welds, is recommended to assure that "skips" or holidays are properly covered . Use contrasting colours for each coat and stripe coating.

It is very important for the safety of the applicator and the proper performance of EURO-basic ES301, that good ventilation be provided to all portions of the enclosed area. Dry air IS NOT a must since EURO-basic ES301, DOES NOT contain solvents, can be applied under severe conditions of humidity.

DISCLAIMER: This is not a specification and all information is given in good faith. Since conditions of use are beyond the manufacturers control information contained herein is without warranty, implied or otherwise, and final determination of the suitability of any information or material for the use contemplated, the manner of use and whether there is any infringement of patents is the sole responsibility of user. Manufacturer does not assume any liability in connection with the use of the product relative to coverage, performance or injury. For application in special conditions consult manufacturer for detail recommendations.

WARNING: Cause eye and skin irritation. Reaction vapour may cause respiratory irritation in sensitive individuals. May cause allergic skin reaction. Avoid breathing vapours. Do not get in eyes on skin or clothing. ear eye and skin protective equipment. Use appropriate respirator, it is recommended to avoid potential respiratory irritation. Wash skin thoroughly after use and water. Call a physician. Launder clothing before reuse. If not breathing give artificial respiration, preferably mouth-to-mouth, and call physician.

BURNS: Exothermic reaction causes product to heat which is normal. Be careful handling after mixing product. Use gloves.

FIRST AID: In case of eye contact immediately flush with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash skin contact area with soap.